| No. | Brand | S | d | A | H | T | Y | F | N |
| 11.35.2620.001.41.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 12.50.2559.201.49.1502 | Standard 5 | - | 160 | - | - | - | - | - | - |
| 2 052 | Rollix | - | 180 | - | - | - | - | - | - |
| 192.50.3550.990.41.1502 | Standard 5 | - | - | - | - | - | - | - | - |
| 191.40.4000.990.41.1502 | Standard 5 | - | - | - | - | - | - | - | - |
| 192.50.5600.990.41.1502 | Standard 5 | - | 9.25 in | - | - | - | - | - | - |
| 22 0641 01 | Rollix | - | 10.0000 in | - | - | - | - | - | - |
| 91.50.2446.990.41.1502 | Standard 5 | - | - | - | - | - | - | - | - |
| 161.45.2366.890.11.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 11.50.3747.001.49.1502 | Standard 5 | - | 75.000 mm | - | - | - | - | - | - |
| 26 0541 01 | Rollix | - | 20 | - | - | - | - | - | - |
| 36 0541 01 | Rollix | - | - | - | - | - | - | - | - |
| 121.50.6700.990.41.1502 | Standard 5 | - | 200 mm | - | - | - | - | - | - |
| 191.50.3550.990.41.1502 | Standard 5 | - | 1120 mm | - | - | - | - | - | - |
| 161.45.2510.891.41.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 39 0541 01 | Rollix | - | 180 mm | - | - | - | - | - | - |
| 191.32.2500.990.41.1502 | Standard 5 | - | - | 185.00 mm | 271 mm | - | - | - | 18 mm |
| 192.25.2240.990.41.1502 | Standard 5 | - | - | - | - | - | - | - | - |
| 192.40.3150.990.41.1502 | Standard 5 | - | 0.8121 in | - | - | - | - | - | - |
| 62.50.2800.001.49.1504 | Standard 5 | - | - | - | - | - | - | - | - |
| 7 0380 01 | Rollix | - | 2.9518 in | - | - | - | - | - | - |
| 161.40.2368.891.41.1503 | Standard 5 | - | 457.200 mm | - | - | - | - | - | - |
| 2 0308 01 | Rollix | - | 80 mm | - | - | - | - | - | - |
| 11.35.2220.001.41.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 7 0573 | Rollix | - | - | - | - | - | - | - | - |
| 191.32.4000.990.41.1502 Standard 5 Slewing Ring Bearings | B - Cone Width:2 in; da - Cone Frontface Backing Diameter:17.4 in; G2 - Heat Generation Factor (Rib-Roller End):671.4; db - Cone Backface Backing Diameter:17.6 in; Ab - Cage-Cone Frontface Clearance:0.14 in; Cone Part Number:L269140; d:16.8125 in; K - Factor8:1.76; Design Units:Imperial; R - Cone Backface To Clear Radius3:0.13 in; C0 - Static Radial Rating:396000 lbf; Cg - Geometry Factor:0.185; G1 - Heat Generation Factor (Roller-Raceway):3088.3; |
| 191.50.4500.990.41.1502 Standard 5 Slewing Ring Bearings | Prod_Type3:SABB_SA_TB; da:86; C0:43; hidTable:ecat_NSSAB; KBRG:1354; cyl count:13; X0:1; yobi:2315K; mass:4.67; groove outer:145.875; PCD:117.5; Y2:2.5; C:125; D_a:149; Y0:1.7; SRIX:0.1; LangID:1; CAng:14.323; Y3:1.6; e:0.38; |
| 91.50.2644.990.41.1502 Standard 5 Slewing Ring Bearings | Dimension A:4.00 in; Shaft Size Type:Imperial; Pre Install Clearance Min:0.0037 in; Dimension D Min:10.81 in; Pre Install Clearance Max:0.0047 in; Housing Style:Four-Bolt Pillow Blo; C - Dynamic Load (Basic):66900 lb; Dimension H:1.50 in; Oil Lubrication - M/N Seal:1400 rpm; Float:0.083 in; Full Timken Part Number:QVPK17V212SB; Oil Lubrication - T Seal:2400 rpm; Y1 - Geometry Factor:3.07; Shaft Size :2-3/4 in; |
| 7 0489 11 Rollix Slewing Ring Bearings | Dimension L:20.0 in; Bearing - Housing - Seal UPC:013992078117; Dimension H:6.378 in; Note:This product line wa; Bearing Number:MSM115BR; Bearing - Housing - Seal:MSM115BRHHTPS; Support Type:Four-Bolt Plummer Bl; Dimension H2:14.6 in; Cr - Dynamic Load Rating:102063 lbf; Pillow/Plummer Block Style:Split Cylindrical Ho; Weight:168 lb; Series Type:Medium Series; Cor - Static Load Rating:133087 lbf; Housing Width:6.3 in; |
| 12.50.3739.001.49.1502 Standard 5 Slewing Ring Bearings | Seal Type:Aluminium Triple Lab; Bearing Number:HSM240BX; Series Type:Heavy Series; Dimension P:1.9 in; Cr - Dynamic Load Rating:426238 lbf; Shaft Size:240 mm; Support Type:Round Flange; Maximum Speed:700 rpm; Bearing UPC:013992024107; Dimension T:35.0 in; Dimension N:27.252 in; Dimension R:31.3 in; Dimension V:0.3 in; Bearing - Housing - Seal:HSM240BXHATL; Note:This product line wa; Cor - Static Load Rating:626992 lbf; |
| 162.45.2510.891.41.1503 Standard 5 Slewing Ring Bearings | Lockwasher and Lockplates:MB8; L1:36.00 mm; Weight:0.22 Kg; d1:1 1/4 in; Locknut:KM8; C:10 mm; D3:58 mm; G:M40x1.5; |
| 11.35.2620.001.41.1503 Standard 5 Slewing Ring Bearings | L11:102.00 mm; Taper:1:12; Weight:1.47 Kg; Appropriate Hydraulic Nut:HMV28; d1:125.00 mm; b:15 mm; Thread D12:M140x2; Appropriate Withdrawal Nut No.:KM28; L:98.00 mm; |
| 11.50.3747.001.49.1502 Standard 5 Slewing Ring Bearings | da - Cone Frontface Backing Diameter:83.06 mm; C90 - Dynamic Radial Rating (90 million revolutions)4:53000 N; Ab - Cage-Cone Frontface Clearance:3 mm; Y - ISO Factor9:1.51; Da - Cup Frontface Backing Diameter:119.90 mm; Cg - Geometry Factor:0.0851; G2 - Heat Generation Factor (Rib-Roller End):26.3; Cage Type:Stamped Steel; Cone Part Number:X33115-SA; Aa - Cage-Cone Backface Clearance:2.3 mm; a - Effective Center Location3:-7.4 mm; |
| 12.30.2538.000.11.1503 Standard 5 Slewing Ring Bearings | Ew:178.5; DI_:132.5; SBRG:2; D_a max:189; SDM_:155.5; da:121; C:229; C_conv:229000; DA_:23; C0:272; KBRG:4121; D_b max:189; d:110; mass:4.81; LangID:1; r:2.1; yobi:NF222W; D_:200; hidTable:ecat_NSCLDR; Z_:15; |
| 11.50.2987.001.49.1502 Standard 5 Slewing Ring Bearings | Seal:LO528; Bolt Qty:2; J:420 mm; Shaft Diameter d:125 mm; H:302 mm; Jmax:427 mm; L:500 mm; Housing Mass:39 Kg; C0 Static Load Rating:1060; A2:223 mm; Material :Cast Iron; Housing:SNT 528; Max Grease Speed:2200; Locknut:KM28; N1:42.00 mm; G:M30; Adapter Sleeve1:H3128; Lockwasher:MB28; C1 Dynamic Load Rating:863; A:205.00 mm; |
| 192.25.2240.990.41.1502 Standard 5 Slewing Ring Bearings | Series:385; Ca90 - Dynamic Thrust Rating (90 million revolutions)7:3480 lbf; a - Effective Center Location4:-0.12 in; C90 - Dynamic Radial Rating (90 million revolutions)5:5740 lbf; Aa - Cage-Cone Backface Clearance:0.03 in; Cone Part Number:386AS; R - Cone Backface To Clear Radius3:0.14 in; C1 - Dynamic Radial Rating (1 million revolutions)6:22200 lbf; C90(2) - Dynamic Radial Rating (Two-Row, 90 million revolutions)2:10000 lbf; |
| 12.50.3839.001.49.1502 Standard 5 Slewing Ring Bearings | r:2.1; DE_:124.5; Macha rpm:8500; dc min:85; TSR rpm:5300; DI_:82.5; da:76; yobi:NU313ET7; B_:33; mass:2.22; C:181; r1:2.1; C0:191; KBRG:4142; C_conv:181000; Fw:82.5; Oil rpm:5300; DA_:21; ra:2; dd min:93; |
| 161.50.2660.891.41.1503 Standard 5 Slewing Ring Bearings | X2:0.67; yobi:240/600CAMK30E4; Y3:2.3; mass:529; e:0.3; X0:1; Oil rpm:320; C0:15100; hidTable:ecat_NSSPHR; TSR rpm:300; DE_:800.088; D_a min:772; SIR:109; D_:870; C:6600; ALPHA_:0.198; Y0:2.2; B_:272; ALP1:11; ra:5; |
| 121.50.6000.990.41.1502 Standard 5 Slewing Ring Bearings | Dimension H2:35.4 in; Housing Width:12.0 in; Pillow/Plummer Block Style:Split Cylindrical Ho; Dimension J1:34.0 in; Maximum Speed:500 rpm; Dimension H:17.756 in; Series Type:Medium Series; Dimension L:43.0 in; Dimension K:11.0 in; Support Type:Eight-Bolt Plummer B; Dimension H1:2.6 in; Bolt Size:8 x M36; Bearing - Housing - Seal:MSM340BXHHTPS; Dimension J2:26.0 in; Cr - Dynamic Load Rating:447145 lbf; |
| 61.50.1900.001.49.1504 Standard 5 Slewing Ring Bearings | C1 - Dynamic Radial Rating (1 million revolutions)6:188000 lbf; G2 - Heat Generation Factor (Rib-Roller End):95.5; G1 - Heat Generation Factor (Roller-Raceway):704.9; C90 - Dynamic Radial Rating (90 million revolutions)5:48800 lbf; db - Cone Backface Backing Diameter:8.11 in; K - Factor8:1.83; B - Cone Width:2.6875 in; Aa - Cage-Cone Backface Clearance:0.18 in; Ca90 - Dynamic Thrust Rating (90 million revolutions)7:26600 lbf; |
| 21 0541 01 Rollix Slewing Ring Bearings | Bearing Type:Split Cylindrical Ex; Note:This product line wa; Cor - Static Load Rating:178049 lbf; Shaft Size:160 mm; Dimension K:110 mm; Dimension L:530 mm; Maximum Speed:1320 rpm; Support Type:Four-Bolt Plummer Bl; Dimension H2:396 mm; Dimension H:180 mm; Bearing UPC:013992028822; Bolt Size:4 x M24; Housing Width:6.8 in; Pillow/Plummer Block Style:Split Cylindrical Ho; Series Type:Light Series; Dimension M:190 mm; |
192.40.2800.990.41.1502 Standard 5 Slewing Ring Bearings Video
192.40.2800.990.41.1502 Three-row Roller Slewing Bearing
192.40.2800.990.41.1502 Three-row Roller Slewing Bearing Internal Gear 2460x3038x220- 192.40.2800.990.41.1502 bearing,Seals Type:Seal
Rd 900 Series Rothe Erde Brand Turntable ... - Tradesparq
191.40.4500.990.41.1502,192.40.2800.990.41.1502,192.40.3150.990.41.1502. 192.40.3550.990.41.1502,192.40.4000.990.41.1502,192.40.4500.990.41.1502
Rothe erde slewing bearing standard RD900
192.40.2800.990.41.1502, 2800, 3213, 3038, 2460, 220. 192.40.3150.990.41.1502, 3150, 3683, 3388, 2794, 220. 192.40.3550.990.41.1502, 3550, 4171, 3788
Buy 192.40.2800.990.41.1502 Rothe erde slewing bearing
Buy 192.40.2800.990.41.1502 Rothe erde slewing bearing from HongKong EVEN Slewing Bearing Co,.Ltd，RKS Series Slewing Bearing Distributor online
192.40.2800.990.41.1502 of ... - Rothe Erde slewing bearing
Jul 25, 2014 - 192.40.2800.990.41.1502 of Rothe Erde slewing bearing. We are Luoyang JCB Bearing Technology Company, working on industry of slewing
192.40.2800.990.41.1502 Drawing of Rothe Erde slewing
192.40.2800.990.41.1502. Size：; Language： English; Categories： Drawing; Download. Copyright @2002-2012 Luoyang JCB Bearing Technology Co., Ltd | All
Rothe Erde Turntable Rotary Bearing , Xbr Slewing Bearing
191.40.4500.990.41.1502,. 192.40.2800.990.41.1502,192.40.3150.990.41.1502. 192.40.3550.990.41.1502,192.40.4000.990.41.1502,. 192.40.4500.990